Open manual gear tips skills common mistakes operation analysis


Many drivers of the manual transmission model are either unskilled or because they are not accustomed to shifting gears. Even when the vehicle speed is increased to a higher level and the vehicle does not match the speed and speed, the original gear position remains unchanged. In fact, this low-speed high-speed approach increases the engine load and damages the engine. Don't be lazy to drive, shift gears according to speed.

For a long time in the semi-clutch state, some drivers are accustomed to stepping on the clutch when the left foot is on the car, thinking that this can better maintain the control of the vehicle, but in fact, this practice is extremely damaging to the clutch plate. Especially when the vehicle is running at a high speed, a long half-clutch state will rapidly wear the clutch plate. In addition, the second block start will also lead to premature clutch damage. A block start is beneficial to any vehicle.

We can always see when shifting without full separation. Some impatient owners are busy catching up when the clutch is not stepped on the end. This not only makes it difficult to accurately position the gear, but also operates it for a long period of time. Transmission is a fatal injury. Although automatic transmission models do not have the problem of stepping on clutch shifts, many drivers hurriedly hang up the P gear when the vehicle is not completely stopped. The gearbox is also unable to withstand the situation in which the vehicle condition does not match the operation.

It is often difficult for the road lad to jump up and observe the shock absorbers, springs, and suspension of the vehicle, but they are also vulnerable parts of the vehicle. When you cross the ditch, you slow down in advance, instead of rushing the car hard. This not only guarantees comfort, but also protects shock absorbers, springs, and suspensions. Many car owners jumped up when they were on the road and wanted to show their superior driving skills. Actually, maybe one time, the vibration or spring of the vehicle will no longer match your operation. Similarly, not overloading not only improves fuel economy, but also protects automotive components such as suspension.

Frequent operation of the combination switch lighting flashes the vehicle owner to feel good, but everyone knows that frequent switching increases the chance of damage to the combination switch. Because when the switch is turned on, the current through the contacts of the switch is much higher than usual, and in the half-split half-split state, the spark may burn the contacts.

To make the water jet forced to work When the winter temperature is low, the water spray nozzle is frozen, the owner should not forcibly spray glass water. This will only damage the water pump, the owner can wait for the vehicle to start, the vehicle temperature up, the frozen water nozzle thaw and then spray. The same is true of the wipers, and the cold wipers do not provide the necessary cleaning results.

There are many tire reminders about tire treads, but one thing to note is that the side of the tire is thinnest. Therefore, when the owner steps up or crosses the road, special attention must be paid to the protection of the sidewalls. Do not collide with the front side. To the side, the side of the collision is even worse than the front.

Keeping the glass lifter in place does not release a lot of vehicle glass. The electric switch does not work or the window glass cannot be lifted into place. This is also related to the mistakes of daily operations. When using the electric glass lifter to lift the glass, when the glass is lowered to the bottom or raised to the top, be sure to loosen it in time. Otherwise, the mechanical parts of the vehicle will be relatively strong and the motor will naturally be destroyed.

The old driver, who had the experience of pulling on the brakes and driving, said that he should use gears more when he was controlling the speed, anticipate early, diligently shift gears, and use less brakes. In particular, let the engine brake when downhill, occasionally supplemented by braking, do not step on the brake downhill, so you can protect the brake pads. Do not forget to release your hand before starting the vehicle. Pulling a hand to brake the car is one of the most wearable brake pads.

The turning angle of the steering wheel is too large because it is often used. The booster pump is also a fragile part of the vehicle. When the driver is playing in the direction, when he hits the head, he should return a little. Do not let the booster pump stay in a tight state for a long time, which will help to prolong the life of the booster pump.


ASTM A320 Threaded Rods

We are China manufacturer of high quality grade l7, l43 Threaded Rods and threaded bars in astm a320 standard. Our advantages and more services of threaded steel rods includes:

1) Wide range of diameters from 1/2" - 4"

2) Customized Length from 100mm to 12000mm

3) Good threads at 60 degree

4) Good straightness: 1mm/m max

5) Even hardness on whole bars

5) Proper mechanical properties

7) Full sets of testing equipment: Surface, Dimenstion. Mechanical properties testing

8) Fast delivery time

astm a320 l7,Astm A320 Threaded Rods,astm a320 l7 threaded rod,astm a320 l7 threaded bar,astm a320 l7 steel bar

SHANDONG LE REN SPECIAL STEEL CO., LTD. , https://www.sdthreadedrods.com